If a Zanussi dishwasher is faulty, an error code is displayed. So the self-diagnosis system informs the user that a breakdown has occurred in the car. The value of the code allows you to quickly find the cause of the breakdown, since each combination of characters indicates a certain type of malfunction.
Decipher the errors of the Zanussi dishwashers. Our table will help you.
How Zanussi Trouble Codes Decrypt
If the panel of your dishwasher is not equipped with a display, an error will appear on the indicators. The number of flashes of the light indicates a specific malfunction.
Those who first saw an error on the scoreboard need to restart the equipment. There may have been a system crash. How to restart PMM:
- disconnect the machine from power;
- wait 20 minutes;
- reconnect the PMM;
- look at the display.
If the code is highlighted again - you need to look for a problem. If the display does not show anything, then start the dishwasher as usual.
Malfunction code | The number of indicator flashes after a pause of 5 seconds | What does it mean | Reasons for the appearance | DIY repair |
i10 | 1 | There is no water in the PMM tank. | 1. The inlet tap is closed. 2. The water supply is off. 3. Clogged or pinched inlet hose. 4. The filter is clogged. 5. Problems with the operation of the inlet valve. | 1. Turn the valve, it may have been poorly opened. 2. Check for water in the tap. 3. Inspect the inlet hose. Unscrew one end from the machine body and check for blockage. 4. Pull out the filter screen. Clean out debris. 5. Diagnose the intake valve. Replace it. |
i20 | 2 | What does the error mean: the system does not drain the water after washing the dishes. | What happened: 1. There were problems with the pressure switch. 2. The drainage pathway is clogged with food debris. 3. The impeller of the pump is blocked, or the pump itself is defective. 4. The drain hose is clogged or pinched. | How to fix the situation: 1. Check and replace the pressure switch. 2. Inspect and clean the drain filter, pump, hose. 3. Check the impeller of the pump. Perhaps it is blocked by glass fragments from the dishes. 4. Correct the hose, it should be evenly connected to the body. |
i30 | 3 | Protection "Aquastop" has worked. | There was a leak in the dishwasher. The float sensor gave a signal to the module. | Inspect such parts and assemblies: PMM tank, hoses and their connections, door seals. Leak must be fixed. |
i50 | 5 | The triac of the engine (circulation pump) burned out. | Triac short circuit on the electronic board. The pump performs work at high speeds without stopping. | Repair of the control board or its replacement. |
i60 | 6 | Meaning: Water does not heat up. Dishes are poorly laundered. | 1. The heater is broken. 2. The contacts of the heater are broken. 3. Problems with the circulation pump. Poor water circulation in the car. 4. The main module is defective. | What can be done: 1. Install a new heating element. 2. Check the contacts of the heater, replace the burnt parts. 3. Diagnose the circulation pump. 4. Check the main module. |
i70 | 7 | There are problems with the NTC thermistor. | 1. Broken sensor wiring due to short circuit. 2. Thermistor failure. 3. Problems with the electronic unit. | 1. Replacing burnt parts of the wiring. 2. Installing a new thermistor. 3. Change of electronic unit. |
i80 | 8 | EEPROM memory problems. | The program cannot be installed because the control module is defective. | Flashing or replacing the main module. |
i90 | 9 | A software error has occurred. | The electronic board is not working properly. Unable to install the program. | You need to install a new board in the Zanussi dishwasher. |
iA0 | 10 | The dishwasher does not work in the dishwasher. | The causes of the problem: 1. Spray nozzles clogged. 2. The PMM engine does not work. | 1. Clean the nozzles with a thin object. 2. Diagnose and replace the engine. |
ib0 | 11 | The turbidity sensor is broken. | The sensor gives incorrect readings. Washing is carried out with the installation of "heavy pollution". | Turbidity sensor change to a working device. |
iC0 | 12 | There is no communication with the user interface. | The dishwasher stops working, trying to reconnect. | You need to wait for the resumption of communication or call the wizard. |
id0 | 13 | The engine is broken. The tachometer does not give a signal. | 1. Damage to the engine circuit. 2. Engine blockage. 3. The contacts of the tachometer are broken, or it itself is faulty. | Self repair: 1. Check the wiring of the engine and tachodachik. 2. Elimination of blockage. 3. Replacing the tachometer. |
iF0 | 14 | Waiting exceeded. Water does not drain. | 1. Wrong location of dishes in the hopper. 2. The drain filter is clogged. 3. High level of foam in the tank. 4. Faulty pressure switch. | 1. You need to open the hopper and place the dishes correctly so that water does not accumulate in the container. 2. Cleaning the pump filter. 3. Removing excess foam. Dosage of detergents. 4. Installing a working pressure switch. |
Having studied the table, you can begin to search for damage in the Zanussi dishwasher. If you adhere to the manufacturer's recommendations, the equipment will break much less frequently. If the warranty period is valid, contact the service center.